Menu

Teel Tech Riff Kit

What's Included:

The Teel Tech Riff Kit includes the Riff Box V2, as well as essential complementary parts that enable examiners to get the most from the box for forensics. All students of the TeelTech JTAG classes receive the TeelTech Riff Kit at class. Packaged in a convenient case, the kit includes:

  • Riff Box V2
  • Connector ribbons
  • Small and large solder boards
  • Complete Molex connectors and boards
  • Practice solder board
  • Ohms
  • Test leads
  • Enameled wire
  • TeelTech Solder Guide with coordinated 3ft rainbow wire strips

TEEL TECH RIFF KIT

Price: USD $275.00

Part #AP-RIFFK

About the Riff Box 2

riff box 2 close up

Introducing the new RIFF Box 2 

It’s been six years since the initial release of the original RIFF box by Rocker Team, and the wait for the new and improved RIFF Box is finally over. The new development supports regular users, but also offers improved features for more advanced users. The new hardware has been designed to facilitate a wide array of communication protocols, including those of highest importance for starters.

The new RIFF Box 2 hardware and software is fully compatible with Windows 10, simplifying the installation process. Just connect RIFF Box 2 to Windows 10 based PC and everything is automatically installed. For older versions of Windows, custom drivers have been provided along with a RIFF JTAG Manager installer.

RIFF Box 2 Specifications

RIFF BOX v2 H/W Specification

  • Dual-core Cortex-M4 MCU @ 204MHz;
  • PC to Box USB (Device) Speed: Hi-Speed (480 Mbps);
  • Box to Device (Host) Speed: Full-Speed (48 Mbps);
  • SD/MMC Interface with 1-Bit (DAT0) and 4-Bit (DAT0-DAT3) Bus Width support and SD_CLK up to 52 MHz;
  • UART Interface;
  • RIFF™ Smart Probing Feature;
  • Level-adjustable 23 GPIO Lines (1.65V to 3.6V) for interfacing a range of devices and protocols, such as NAND, SPI, I2C, Pin Finder, etc.;
  • 4 fixed 3.3V GPIO Lines;

RIFF BOX v2 Interface Specification

  • 20-Pin Male Connector:
  • JTAG Interface: TRST, TDI, TMS, TCK, RTCK, TDO and NRST;
  • SWD (Serial Wire Debug) Interface: SWCLK, SWDIO (SWDIO and SWCLK are overlaid on the TMS and TCK pins);
  • 30-Pin Male Connector:
  • SD/MMC Interface 1/4Bit @ 52MHz;
  • Level-adjustable 23 GPIO Lines (1.65V to 3.6V);
  • USB Device Connector: connects the Box with PC @ Hi-Speed (480 Mbps), approx. 20 MByte/sec;
  • USB Host Connector: connects the Box with USB devices @ Full-Speed (48 Mbps), approx. 1.5-2 MByte/sec;
  • RJ-45 Connector;
  • RIFF™ Smart Probing Feature;
  • UART Port;
  • 4 Fixed 3.3V GPIO Lines;

RIFF Box v2 software:

  • RIFF JTAG Manager
  • RIFF Remote helper
  • RIFF Admin client / SN reader
  • RIFF Box USB drivers

Supported SD/MMD Revisions:

Revisions 1.0 to 1.7 (for MMC: v4.0, v4.1, v4.2, v4.3, v4.41, v4.5, v4.51, v5.0) and higher

Supported JTAG Cores:

  • ARM7,
  • ARM920,
  • ARM926,
  • ARM946,
  • ARM7EJS,
  • ARM11,
  • CORTEX-A5,
  • CORTEX-A8,
  • CORTEX-A9,
  • CORTEX-A15,
  • OMAP3430,
  • OMAP3630,
  • OMAP4430,
  • TEGRA2 (CORTEX-A9),
  • TEGRA2 (ARM7),
  • QUALCOMM S3 (ARM7, ARM11, SCORPION),
  • QUALCOMM S4 (ARM7, ARM11, SCORPION),
  • NOVATHOR,
  • PXA270,
  • PXA312
  • MIPS32™ IR5Bit,
  • MIPS32™ IR8Bit,

The Riff Box 2 is Featured in our JTAG Training Classes