NuProg-E UFS /eMMC Programmer
About the NuProg-E UFS / EMMC Programmer
Product Code: AP-DEDIP-NUPROG-E
The NuProg-E is a professional engineering tool that has been innovated for programming mass flash storage with its speed and reliability. This is achieved by utilizing industry interface standards of interconnect layer specifications, M-PHY and Unipro from MIPI® Alliance. Together with a built-in SuperSpeed® USB 3.0 for high speed communication, it is an efficient tool for you to focus on application analysis and product development.
The NuProg-E programmer supports Universal Flash Storage (UFS), eMMC and eMCP which are widely used in mobile devices such as smart phones and tablet computers. Designed with complete functional software and a user friendly interface, it allows the engineer to define UFS‘s Descriptors, Attributes, Flags, LUN and boot partition; in addition it also provide access to eMMC/eMCP’s User Area, Boot, RPMB, GPP and Enhanced area.
Features
High Speed Programming
The NuProg-E offers a built in high speed processor in order to achieve higher programming speeds（Write speed 50MB/s; Read speed 100MB/s） Timing reference ：1GB image file is programmed into Toshiba UFS IC in just 25 seconds
Support UFS and EMMC/EMCP Programming
- UFS part
- Support Descriptors、Attributes、Flags Setting
- Support LUN configured and advance setting
- EMMC part
- Support User Area、Boot1/2 Partition and Extend CSD
- Support RPMB、GPP1~4 and Enhanced mode
- Support all IC package
- Support standard package for UFS and EMMC，or special package for EMCP
- Regular software update
- Palm size and space saving
- Dimension：132 x 75 x 30 mm Weight：104g
- Support USB2.0 and USB3.0 (using power adapter)
- Support Windows7/8/8.1/10
Reballer Kit
Product Code: AP-REBALL-KIT
This kit is used to reball UFS chips and EMMC/EMCP chips.
Kit includes:
- BGA reballing station Chip holder repair base
- 500 g Lead Free SMT low heat solder paste
- Aluminium Foil Tape
- 4 Stencils for BGA221, BGA529, BGA169/162, UFS BGA95
UFS BGA Chip Socket Adapters
N-UFS-065-BGA095-115130-01O
Product Code: AP-DEDIP-BGA095 
* Only For NuProg UFS KLUxGxG1BD-E0Bx_1.0_for_mPOP
N-UFS-065-BGA095-115130-020 Adapter – User Manual
1. The first step of using the N-UFS-065-BGA095-115130-020 Adapter is to ensure the triangle mark on the bottom left of the PCB board lines up with the triangle mark on your DediProg device.
2. Check that Pin 1 of the socket is pointing out to the IC Pin 1 position. Press down on the top of socket to put the IC. Visually check that the connection between the socket and device is correct and your device will be ready for programming.
3. We recommended using a pick up tool for handing the socket. Do not touch the PCB board directly, as dirt and static may cause errors during the programming of the device.
4. Please be sure to remove the adapter from the device after you finish work.
Caution: Incorrect insertion of the socket adapter may cause both device and socket damage.
N-UFS-050-FBGA153-115130-02O
Product Code: AP-DEDIP-FBGA153
* Only For NuProg UFS 11.5×13 package
N-UFS-050-FBGA153-115130-020 Adapter – User Manual
1. The first step of using the N-UFS-050-FBGA153-115130-020 Adapter is to ensure the triangle mark on the bottom left of the PCB board lines up with the triangle mark on your DediProg device.
2. Check that Pin 1 of the socket is pointing out to the IC Pin 1 position. Press down on the top of socket to put the IC. Visually check that the connection between the socket and device is correct and your device will be ready for programming.
3. We recommended using a pick up tool for handing the socket. Do not touch the PCB board directly, as dirt and static may cause errors during the programming of the device.
4. Please be sure to remove the adapter from the device after you finish work.
Caution: Incorrect insertion of the socket adapter may cause both device and socket damage.
